Showing posts with label wood-shop. Show all posts
Showing posts with label wood-shop. Show all posts

Monday, April 4, 2011

Casework Update


The casework team has been full steam ahead over the past couple of weeks, but we still have a lot of ground to cover. Every room in the house has some casework component and we have taken on the responsibility of completing the casework ourselves, from design to fabrication to installation. At this point, we have finished the majority of fabrication for the kitchen casework and are waiting for the flooring to be installed before we install our cabinets.

In the meantime, we will be setting up a large painting operation at our warehouse on Henson Rd. We decided to use a low VOC paint product to comply with our environmental goals, but with every decision comes some pros and cons. With this decision, the water based paint dries hard - similar to the quality of a lacquer based paint - but it takes about thirty days to cure. Therefore, our small, 10x10 paint booth was simply inadequate for the large amount of painting that we have to do.

We should receive a new order of plywood from A&M Supply within the next couple of days to continue fabricating the cabinets for the swing space and the bedroom. The challenge for these cabinets has been integrating all of the necessary components within them. Integrated into all of our cabinets are the Mitsubishi mini-split units which provide the heating and air for the whole house. In addition to the HVAC, most of the cabinets include recessed lighting, so all of the MEP disciplines are coordinated into one piece of millwork. Needless to say, we will have our hands full, blitzing towards the finish line.

This picture has nothing to do with my post... but its beautiful.

Thursday, January 20, 2011

Honing the Skills

Though we completed our entry door frames and slabs [inner structure] near the end of last semester, there is still a great deal of designing and fabricating to be done on them. Additionally, there are two more doors and a cistern enclosure door to be completed. The past few days have been spent getting our drawings, materials, and skills in line.

Because a new team came on-line just last week, it has been important to get everyone on the same page. Because I spent a great deal of time in the wood-shop last semester, I have been showing newbies Justin and Matt how to use specific tools and fabrication processes so that they will be knowledgeable as the semester progresses. We have started with the simplest [crawl space] door in order to hone our skills. In three days we have gone over how to: 1) take a rough-cut and often warped piece of wood through a jointer, planer, and table saw in order to get it perfectly square; 2) biscuit join the inner slab; 3) rout the plywood faces for a perfect edge; 4) dato cut the corners of the door frame for an optimal gluing surface; and 5) assemble the pieces for a square frame.

Aside from showing off our fresh skills, this list begins to show the importance of understanding the process of building component assembly and fabrication when solving design problems both on the site and in the office/lab during the design and drawing process. In order to draw a manufactured object, one must first know how to manufacture that object.

For example: today Matt, Justin and I went to research some Andersen hardware for our doors. Needing all entry hardware to match [between our Andersen french doors and self-fabricated doors] we are required to use a specific hardware which requires us to rout mechanical channels into the edges of our fabricated doors. It was a culminating moment for me to see us work through this multi-faceted problem together. Now that Matt and Justin have a sense of familiarity with the fabrication process, it is easy for us to have intelligent problem-solving conversations about how we can fabricate these doors to work with our complex hardware. It will only get easier as we become more adept in the fabrication process.

Being familiar with how something is built only pushes a design further because it allows us to fix an issue before it becomes one. As we acquire more knowledge about building methods and tools, we bring compounding options on how to solve a single problem. This honing of skills will only help us as we begin to work through even more complex designs of details - such as our hidden-opaque-window-assembly [even the name is complex] due next week.

For some of us graduation is just around the corner, making it easy to think about how these skills apply to an office environment. Throughout this process of designing, testing, redesigning, building, and repeating as necessary, we will be able to pass this knowledge of design and process on to our peers and co-workers, allowing us to improve overall design intent from large to small-scale, and effectively enhance collaborative energy and problem solving in an office environment.